551501 (1/2" X 1 1/2")
551502 (1/2" X 1")

Rectangular Hangrail

1/2" X 1½" and 1/2" X 1" rectangular hangrail,16 Guage, mirror polish chrome. Standard sizes as shown. May be ordered cut to size. Additional cutting charge may apply.

702101
Tightening Thumbscrew Use With Series 10 or 20
Thumbscrews tighten faceout or shelf bracket against slotted standard to prevent side to side sway.

702102
Tightening Thumbscrew (.125") Use With Series 30 Only
Used for same application as part # 702101.

752401

Table/Bench Leg

18½"H table or bench leg. Constructed of 1" X 1" X 16 Ga. steel tubing with a thread nylon glide leveler. Top plate is 4" X 3" x .125" with four screw holes. Mirror polish chrome. Note: Legs may be cut to size or custom ordered for longer lengths.

991401

Flush End Cap

Fits ½" X 1½" X 16 Ga. rectangular tubing, friction fit, mirror polish chrome.

991402

End Cap With One Tab

Fits ½" X 1½" X 16 Ga. rectangular tubing, friction fit, mirror polish chrome.

991403

End Cap With Tabs Up and Down

Fits ½" X 1½" X 16 Ga. rectangular tubing, friction fit, mirror polish chrome. Tabs on both the top and bottom.

991404

Rectangular Tubing Splicer

Fits ½" X 1½" X 16 Ga. rectangular tubing, chrome. Joins two pieces of hangrail with a tight friction fit.

991405

Extended End Cap

1" extension on end cap, fits ½" X 1½" X 16 Ga. rectangular tubing, spring fit, mirror polish chrome. Used to finish the end of hangrail when it dead ends in the saddle of a hangrail bracket.

991406

End Cap With One Tab

Fits ½" X 1½" X 16 Ga. rectangular tubing, spring fit, mirror polish chrome.

991409
End Cap With One Tab

991410
Flush End Cap

Fits ½" X 1" X 16 Ga. rectangular tubing, spring fit, mirror polish chrome.

992109

Plastic Hangrail Protector

Protects ½" X 1½" rectangular tubing hangrail or faceouts from hanger scratches. PVC channel is ½" wide with ¼" long legs, snaps on to hangrail. Colors: Black or Clear.

Solid Steel Pucks

All pucks are 3/8" thick and available in diameters shown, tapped for 1/4"-20 threaded stem. Mirror polish chrome.

Set screw available only on 1" diameter pucks (#992115). Threaded stems or hanger bolts available separately.

992120 (Puck)
992138 (Pin)

Puck And Pin Shelf Rest System For ¼" Holes

1" X ½" thick puck with flat machined shelf resting area. The ¼" pin is screwed into puck and pressed into drilled holes to act as shelf rest.

992116

Threaded Stems For Pucks

¼"-20 threaded stems, zinc plated. Call for special size needs.

992118

Chrome Steel Hangrail Protector

1/8" thick X ½" wide chrome plated steel hangrail protector to prevent hanger scratches, predrilled with countersunk holes for rivets or screws. May be ordered separately or may be installed on hangrail or brackets.

992139

Hanger Bolt

One end threaded for wood, opposite end threaded 1/4"-20 to receive puck, nut or other machine threaded item.

992123 (Gray Rubber)
992136 (Clear PVC)

Shelf Rest Cushion
For use on all shelf rests.

Clear PVC Protector for Hook Tips
Safety tip for display hooks.

800010

Clear Acrylic Scarf Ring
Rings are made of 3/16" diameter acrylic and are 1 1/2" in diameter.

992142

Clear PVC Stick On Bumper
.2"H X .4"W clear cushion for glass shelves or to prevent shelves from sliding. Adhesive back, 56 per sheet, available only in full sheets.

Utility Clip for 1/2" X 1 1/2" Tubing
Clip snaps on to tubing to provide lip for shelf rest or attachment point for signage. Can be used with rubber cushions. Pol. chrome

Metal Shelf Rests For Blade Type Shelf Brackets

Chrome finish. Order cushions separately. Series 10 for blade thickness .065"-.090" Series 20 or 30 for blade thickness .125".

Plastic Shelf Rests For Blade Type Shelf Brackets

Clear cushions included (installed). Series 10 for blade thickness .065"-.090" Series 20 or 30 for blade thickness .125"

992144

Center

Metal Shelf Rests For Rectangular Tube Shelf Brackets

Fits ½" Wide Rectangular Tubing. Chrome finish. Order cushions separately.

992145

Left/Right

Metal Shelf Rests For Rectangular Tube Shelf Brackets

Fits ½" Wide Rectangular Tubing. Chrome finish. Order cushions separately.

992150 (Square)
992151 (Round)

Anchor/Foot Plates

11 Gauge anchor or foot plates with 1/4"-20 threaded nuts for use in fixure construction. Square plate is 21/2" square. Round plate is 2" . Raw or zinc finish.

992171

Clear PVC Washers

Clear .078" thick plastic washers to cushion pucks or other steel surfaces when contacting glass or finished surface.

O.D. I.D. -01 .987" .35" -02 .750" .312"

992173

U-Clip for Glass or Acrylic

Clip fits 3/8" glass or acrylic sheet. Made of .090" thick cold rolled steel, threaded 1/4"-20. Mirror polish chrome.

992174

Decorative Bolt

Bolt has finished chrome head, ¾" X 1/8" thick. Thread is ¼"-20 and 1¼" long. Designed for finished or presentation surfaces.

992175(Nut)

992176 (Bolt)

Chrome Connector Nut/Bolt

Connector nut and bolt for dress finish. Head is 9/16" and requires 5MM hex wrench. Bolt available in lengths of 1", 1¼" and 17/16" lengths. This connector nut and bolt set also required for use on glass mount faceouts.

992177

2" Diameter Steel Ball

2" X 20 Ga. steel ornamental ball, mirror polish chrome, with 1/4"-20 X 2"L threaded stem.

992180

Display Hook for Wood or Acrylic Panel

3/16" wire with safety ball, 45° bend, 1" long X ¼"-20 threaded end with finishing collar, includes retaining nut, brushed or chrome finish. Hook designed for use in a through panel application.

992181

Machined Display Hook

21/4"L ornamental display hook, 1/4" rod with 1/2" X 1/4" thick end puck and finish collar. Threaded 1/4"-20 for through panel application. Mirror polish brass.

992192

Wire Divider (Wicket)

An 8"H wire divider with a 1/2" wide base, 1/8" thick. Wire is 3/16" and width is 3" or 6" O.C. Finished mirror polish chrome or available in other sizes on special order.

Shoes and Channels Available on Special Order
Custom shoes and channels for glass wall or other free standing glass fixtures. Available in any size to fit your special needs. All pieces include heavy duty construction with nylon levelers. Attachments and connectors can be customized to the needs of your fixtures. Standard pieces available. Call for more information.

All Steel Construction
Available in any plated or brushed finish. Thicknesses available include .070", .125" and .25".

702119 (Left)
702120 (Right)

Adaptor For Blade Type Shelf Brackets

Fits all shelf bracket series. Attaches to front of bracket with nut and bolt so that wood or metal trim molding may be screwed to the front of the brackets. Attachment nuts and bolts included.

Blade Type Molding Adaptor Assemblies

Adaptors fit directly on to all blade type shelf brackets.

Tubular Molding Adaptor Assemblies

Adaptors fit into specially slotted tubular shelf brackets.

Tubular Brackets For Trim Molding

Tubular shelf brackets specially slotted for Tubular Molding Adaptors shown below.

Trim Molding Adaptor For Tubular Type Shelf Brackets
991425 (1/2" X 1 1/2" Tubing)
991426 (1/2" X 1" Tubing)

Fits all tubular shelf brackets. Attaches inside front of tubing, allowing 3/4" of adjustment. Wood or metal trim molding may then be screwed to the front of the brackets. Universal for left or right by turning adaptor upside down. Tightening screw included. Adaptor is used with the specially slotted tubular shelf bracket shown above. The bracket is slotted on the bottom as shown above.